- SHOULD I INSTALL WD MY BOOK SOFTWARE FULL
- SHOULD I INSTALL WD MY BOOK SOFTWARE TRIAL
- SHOULD I INSTALL WD MY BOOK SOFTWARE PC
- SHOULD I INSTALL WD MY BOOK SOFTWARE WINDOWS
What I figured out was that the way to get the My Book recognized during a TI rescue disk boot is different than the steps you take during a normal boot.
SHOULD I INSTALL WD MY BOOK SOFTWARE PC
However, the PC/TI boot disk did not recognize the My Book as the PC had during a normal boot. Then I turned on the My Book, and then connected the cable to the My Book and then to the PC.
SHOULD I INSTALL WD MY BOOK SOFTWARE FULL
I booted from the TI Rescue boot disk, selected Full Mode, and waited for the TI program to fully load. I proceeded based on what I learned about getting the My Book recognized by my PC during a normal boot (without the boot disk). Being able to create an image with the TI boot disk and saving that image to the My Book would let me know that the My Book would get recognized/function when I booted with the boot disk.
SHOULD I INSTALL WD MY BOOK SOFTWARE WINDOWS
I felt that it was important for me to know that if my hard drive became corrupt and windows did not load that I would be able to restore an image from the My Book using the TI boot disk.
![should i install wd my book software should i install wd my book software](https://images.anandtech.com/doci/4952/sshot-28.png)
I wanted to verify that I could create an image using the non-windows environment by using the TI Rescue boot disk.
SHOULD I INSTALL WD MY BOOK SOFTWARE TRIAL
Because of what I learned through trial and error, I thought I knew all I needed to know to create an image using the TI 9.0 3677 build Rescue boot disk, but I was wrong. With this fully understood, I was able to get the My Book recongized by the PC, create an image of my internal drive with TI in the windows envirnoment and have that image saved to the My Book external drive. When you are done with your imaging/restoring with TI in the windows environment and you are ready to disconnect the My Book from the PC, you can "Safely Remove" the My Book through the System Tray icon and wait for the PC to automatically turn off the My Book before disconnecting the drive, or you can turn off the My Book by pressing the button on the front of the drive and wait for the drive to turn off. After a short time, the PC will load the Western Digital Button Manager (blue system tray icon) and the My Book will be useable. Then you have to connect the USB/Firewire cable to the My Book, and connect that wire to the USB/Firewire port. Then you need to fully spinup (turn on) the My Book. To get the My Book recognized by the PC, you must first fully boot your PC. If you plan to pull the My Book from a shelf for a back up (and the My Book has not been connected to the PC for a while) the process is different. What figured out was that the only time the PC will automatically turn on the My Book and recognize it at boot up is when the My Book was attached to the PC when the PC was last shutdown. Based on my reading of the manual, I believed the PC would turn on and recognize the My Book automatically. What I was doing was connecting the My Book to the PC and then turning on the PC. The problem was I thought I could connect the My Book at any time and have the PC recognize the drive. After the initial setup on each PC, I could not get the PCs to recognize the My Book during a normal boot. This is where I ran into my first frustration. I wanted to make sure, I could easily move the drive between my two (2) PCs and have the drive be recognized by each PC. The PC recognized the My Book and everything was fine. I did not install the WD backup program or any other non-essential programs. When I got the drive, I followed the Western Digital instructions to install the basic software/drivers and to make the connections.
![should i install wd my book software should i install wd my book software](https://www.diskpart.com/screenshot/en/std/format-partition/format-1tb-to-fat32/apply.png)
I do not plan on having the drive permanently connected to a PC.
![should i install wd my book software should i install wd my book software](https://www.ubuy.vn/productimg/?image=aHR0cHM6Ly9tLm1lZGlhLWFtYXpvbi5jb20vaW1hZ2VzL0kvNjF6amlLUXpwV0wuX0FDX1NMMTUwMF8uanBn.jpg)
I plan to keep the drive on a shelf or in its box when it is not needed for images or restores. If you are now in the same boat I was in a few days ago, this post may save you some frustration.īefore I start, I want to mention that my plan for the My Book is to use it as a place to store my backup images. The solution is very easy, but it took me some trial and error to figure out. Because I had some frustration trying to make the drive work with my computer (get recognized) and also experienced frustration trying to get the drive to work with the TI 9.0 Rescue boot disk (get recognized), I wanted to share how I got this drive to work. This is not my first USB device, but it is my first external hard drive. It came with USB and Firewire 400 connections. I recently purchased a 250GB Western Digital My Book external hard drive.